Maximum protection against dirt and dust! Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro-Guard 7 filter-the absolute best you can buy! Cold air equals more power! That's why the Magnum FORCE Stage 1 Air Intake System is a must if you want all the power you can get! It replaces the factory air box and stock air filter but REUSES THE STOCK INTAKE TUBEyou still get increased airflow and more horsepower and torque but they cost you less. Incorporating the largest air box (and the largest filter!), this system guarantees your make and model is getting the maximum amount air regardless of the performance upgrades. Roto-molded plastic housings dramatically increase air flow and velocity. The Magnum FORCE Stage 1 Air Intake System retains and works with stock electronics and features heavy-duty 16-gauge steel components with a tough OE-look powder coat finish and sealed or covered trim to lock out hot engine air. Easy to install! All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Patented Pro-Guard 7 Filter is the best! Amazing 99.7% filtration efficiencyno other filter comes close! With five layers of progressively finer medical-grade cotton gauze and two layers of nonwoven polyester fabric, the Pro-Guard 7 offers the best engine protection you can buy! Absolutely essential for the roughest, toughest, dirtiest off-road driving conditions. Tall, rounded, open pleats maximize airflow and extend service intervals (45, 000 miles vs. 15, 000 for stock paper and 10, 000 for foam!). Most filters have built-in expanded metal to prevent collapse under high boost pressures. Best of all, you'll never have to buy another filter again because the Pro-Guard 7 filter can be washed, re-oiled and reused again and again.
Maximum protection against dirt and dust! Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro-Guard 7 filter-the absolute best you can buy! Cold air equals more power! That's why the Magnum FORCE Stage 1 Air Intake System is a must if you want all the power you can get! It replaces the factory air box and stock air filter but REUSES THE STOCK INTAKE TUBEyou still get increased airflow and more horsepower and torque but they cost you less. Incorporating the largest air box (and the largest filter!), this system guarantees your make and model is getting the maximum amount air regardless of the performance upgrades. Roto-molded plastic housings dramatically increase air flow and velocity. The Magnum FORCE Stage 1 Air Intake System retains and works with stock electronics and features heavy-duty 16-gauge steel components with a tough OE-look powder coat finish and sealed or covered trim to lock out hot engine air. Easy to install! All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Patented Pro-Guard 7 Filter is the best! Amazing 99.7% filtration efficiencyno other filter comes close! With five layers of progressively finer medical-grade cotton gauze and two layers of nonwoven polyester fabric, the Pro-Guard 7 offers the best engine protection you can buy! Absolutely essential for the roughest, toughest, dirtiest off-road driving conditions. Tall, rounded, open pleats maximize airflow and extend service intervals (45, 000 miles vs. 15, 000 for stock paper and 10, 000 for foam!). Most filters have built-in expanded metal to prevent collapse under high boost pressures. Best of all, you'll never have to buy another filter again because the Pro-Guard 7 filter can be washed, re-oiled and reused again and again.
Universal-fit filter with velocity-stack base for maximum airflowmore than twice the airflow of stock filters for increased HP and torque! Oiled 4-ply cotton gauze filter has more surface area than the competition for superior filtration of dirt particles High-flow, low-restriction filter incorporating cotton gauze and polyurethane components is more durable than other filtersand reusable!
Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro Dry S oil-free filterthe easiest to service! Cold air equals more power! That's why the Magnum FORCE Stage 1 Air Intake System is a must if you want all the power you can get! It replaces the factory air box and stock air filter but REUSES THE STOCK INTAKE TUBEyou still get increased airflow and more horsepower and torque but they cost you less! Fits American and Imported Cars, Pickups and SUVs. Incorporating the largest air box (and the largest filter!), this system guarantees your make and model gets the maximum amount air regardless of the performance upgrades. Roto-molded plastic housing dramatically increases air flow and velocity. The Magnum FORCE Stage 1 Air Intake System retains and works with stock electronics and features heavy-duty 16-gauge steel components with a tough OE-look powder coat finish and sealed or covered trim to lock out hot engine air. The Magnum FORCE Stage 1 Air Intake System is easy to install! All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Pro Dry S Filter. Easiest to use and never needs oiling! It's the perfect balance of performance, protection and convenience! Offers 99.4% filtration efficiency for engine protection plus 50% higher airflow than stock. Also increases horsepower and torque and improves fuel economy. Pro Dry S Filters incorporates two inner layers of randomly porous dry synthetic fabric to trap dust particles plus inner and outer screens for strength and support. Tall, rounded pleats significantly increase airflow and dust-holding capacity. Easier to service than oil-impregnated or foam filterssimply tap it, vacuum it or wash it with soap and water to clean. Comes with limited lifetime warranty.
Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro Dry S oil-free filterthe easiest to service! Cold air equals more power! That's why the Magnum FORCE Stage 1 Air Intake System is a must if you want all the power you can get! It replaces the factory air box and stock air filter but REUSES THE STOCK INTAKE TUBEyou still get increased airflow and more horsepower and torque but they cost you less! Fits American and Imported Cars, Pickups and SUVs. Incorporating the largest air box (and the largest filter!), this system guarantees your make and model gets the maximum amount air regardless of the performance upgrades. Roto-molded plastic housing dramatically increases air flow and velocity. The Magnum FORCE Stage 1 Air Intake System retains and works with stock electronics and features heavy-duty 16-gauge steel components with a tough OE-look powder coat finish and sealed or covered trim to lock out hot engine air. The Magnum FORCE Stage 1 Air Intake System is easy to install! All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Pro Dry S Filter. Easiest to use and never needs oiling! It's the perfect balance of performance, protection and convenience! Offers 99.4% filtration efficiency for engine protection plus 50% higher airflow than stock. Also increases horsepower and torque and improves fuel economy. Pro Dry S Filters incorporates two inner layers of randomly porous dry synthetic fabric to trap dust particles plus inner and outer screens for strength and support. Tall, rounded pleats significantly increase airflow and dust-holding capacity. Easier to service than oil-impregnated or foam filterssimply tap it, vacuum it or wash it with soap and water to clean. Comes with limited lifetime warranty.
Replaces factory air box and stock air filter Improves airflow up to 75%, throttle response, acceleration and fuel efficiency Increases up to 60 ft-lbs of torqueup to 50 HP gain! More air equals more power! For the automotive enthusiast who wants all the power and torque he can get! Compared to our other systems, the Magnum FORCE Stage 1 intake system replaces the entire stock air induction system. Remembering our motto ""Stock Sucks"", we eliminate the stock air box, the stock air filter and the stock intake tract. The only thing retained is the stock electronics. We make sure that our Stage 1 system, like all our intake systems, works with the stock electronics. Cold air equals more power! In designing out the stock air box, we design in the largest air box that we can for each vehicle application. Even though we make it as large as possible, we are careful to use the stock mounting points. There is no need to cut or drill anything when you install our system. We make the air box as large as possible so that we can get the largest air filter. At first glance you probably won't notice the unique features that we design into each air box. Each of them is there for a purpose, either to make your job of installing the system easier or to improve the performance of your vehicle. Here are a few the features and benefits that distinguish aFe's Magnum FORCE Stage 1 intake systems: 16-gauge powder-coated steel for a durable, OE look and finish Trim sealed or coveredseals out hot engine air Secured PEM-nuts for easier installation Welded and preassembled sheet metal for faster installation Pre-positioned opening for stock attachmentsno dangling wires, relocating hoses or tubes By designing the largest filter for the largest air box, we are able insure that the vehicle is getting the maximum amount of air regardless of the performance upgrades. System uses our conical universal clamp-on filters. Here are some common characteristics of our Pro 5R air filters: 100% poly urethane constructiondurable, resistant to high temperature and chemicals 5 layers of progressively finer medical grade cotton gauze Deep pleats for greater flow and dust holding capacity Rounded pleat geometry for better airflow characteristics Full or modified velocity stack for better airflow characteristics Washable/reusable filter media for longer service life Re oil with our restore kit sold separately (22441G). This Stage 1 Kit reuses the stock intake tube for an economical way to increase air flow horsepower and torquenot as much as Stage 2 (sold separately, 22438G).
Replaces factory air box and stock air filter Improves airflow up to 75%, throttle response, acceleration and fuel efficiency Increases up to 60 ft-lbs of torqueup to 50 HP gain! More air equals more power! For the automotive enthusiast who wants all the power and torque he can get! Compared to our other systems, the Magnum FORCE Stage 1 intake system replaces the entire stock air induction system. Remembering our motto ""Stock Sucks"", we eliminate the stock air box, the stock air filter and the stock intake tract. The only thing retained is the stock electronics. We make sure that our Stage 1 system, like all our intake systems, works with the stock electronics. Cold air equals more power! In designing out the stock air box, we design in the largest air box that we can for each vehicle application. Even though we make it as large as possible, we are careful to use the stock mounting points. There is no need to cut or drill anything when you install our system. We make the air box as large as possible so that we can get the largest air filter. At first glance you probably won't notice the unique features that we design into each air box. Each of them is there for a purpose, either to make your job of installing the system easier or to improve the performance of your vehicle. Here are a few the features and benefits that distinguish aFe's Magnum FORCE Stage 1 intake systems: 16-gauge powder-coated steel for a durable, OE look and finish Trim sealed or coveredseals out hot engine air Secured PEM-nuts for easier installation Welded and preassembled sheet metal for faster installation Pre-positioned opening for stock attachmentsno dangling wires, relocating hoses or tubes By designing the largest filter for the largest air box, we are able insure that the vehicle is getting the maximum amount of air regardless of the performance upgrades. System uses our conical universal clamp-on filters. Here are some common characteristics of our Pro 5R air filters: 100% poly urethane constructiondurable, resistant to high temperature and chemicals 5 layers of progressively finer medical grade cotton gauze Deep pleats for greater flow and dust holding capacity Rounded pleat geometry for better airflow characteristics Full or modified velocity stack for better airflow characteristics Washable/reusable filter media for longer service life Re oil with our restore kit sold separately (22441G). This Stage 1 Kit reuses the stock intake tube for an economical way to increase air flow horsepower and torquenot as much as Stage 2 (sold separately, 22438G).
The only choice if you want all the power and torque you can get! Replaces factory air box, stock air filter and factory intake tube Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro Dry S oil-free filterthe easiest to service! Cold air equals more power! That's why the Magnum FORCE Stage 2 Intake System replaces the entire stock air induction systemso the absolute largest air box (and the largest filter!) can be used for your make and model. This guarantees that your vehicle gets the maximum amount of air regardless of the performance upgrades. To further maximize airflow, heat-blocking roto-molded plastic housings and intake tube (not steel or aluminum) are used to eliminate the kinks, sharp bends and obstructions that can restrict airflow. The tube is tapered to accelerate airflow for more torque and better throttle response. Tube design also means the factory MAF sensor is positioned in the best spot to give you peak performance without triggering the CEL. Other 16-gauge steel components have a durable powder coated finish for an OE look. All trim is sealed or covered to lock out hot engine air. Easy to install! Although the stock air box, filter and intake tract are eliminated, the Magnum FORCE retains and works with your stock electronics. All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Fits American and Imported Cars, Pickups and SUVs. Pro Dry S Filter. Easiest to use and never needs oiling! It's the perfect balance of performance, protection and convenience! Offers 99.4% filtration efficiency for engine protection plus 50% higher airflow than stock. Also increases horsepower and torque and improves fuel economy. Pro Dry S Filters incorporates two inner layers of randomly porous dry synthetic fabric to trap dust particles plus inner and outer screens for strength and support. Tall, rounded pleats significantly increase airflow and dust-holding capacity. Easier to service than oil-impregnated or foam filterssimply tap it, vacuum it or wash it with soap and water to clean. Comes with limited lifetime warranty.
The only choice if you want all the power and torque you can get! Replaces factory air box, stock air filter and factory intake tube Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro Dry S oil-free filterthe easiest to service! Cold air equals more power! That's why the Magnum FORCE Stage 2 Intake System replaces the entire stock air induction systemso the absolute largest air box (and the largest filter!) can be used for your make and model. This guarantees that your vehicle gets the maximum amount of air regardless of the performance upgrades. To further maximize airflow, heat-blocking roto-molded plastic housings and intake tube (not steel or aluminum) are used to eliminate the kinks, sharp bends and obstructions that can restrict airflow. The tube is tapered to accelerate airflow for more torque and better throttle response. Tube design also means the factory MAF sensor is positioned in the best spot to give you peak performance without triggering the CEL. Other 16-gauge steel components have a durable powder coated finish for an OE look. All trim is sealed or covered to lock out hot engine air. Easy to install! Although the stock air box, filter and intake tract are eliminated, the Magnum FORCE retains and works with your stock electronics. All stock mounting points are retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Fits American and Imported Cars, Pickups and SUVs. Pro Dry S Filter. Easiest to use and never needs oiling! It's the perfect balance of performance, protection and convenience! Offers 99.4% filtration efficiency for engine protection plus 50% higher airflow than stock. Also increases horsepower and torque and improves fuel economy. Pro Dry S Filters incorporates two inner layers of randomly porous dry synthetic fabric to trap dust particles plus inner and outer screens for strength and support. Tall, rounded pleats significantly increase airflow and dust-holding capacity. Easier to service than oil-impregnated or foam filterssimply tap it, vacuum it or wash it with soap and water to clean. Comes with limited lifetime warranty.
The only choice for the enthusiast who wants all the power and torque he can get PLUS maximum protection against dirt and dust! Replaces factory air box, stock air filter and factory intake tube Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro-Guard 7 filterthe best you can buyperiod! Cold air equals more power! That's why the Magnum FORCE Stage 2 Air Intake System REPLACES THE ENTIRE STOCK AIR INDUCTION SYSTEMso the absolute largest air box (and the largest filter!) can be used for your make and model. This guarantees that your vehicle is getting the maximum amount of air regardless of the performance upgrades. To further maximize airflow, heat-blocking roto-molded plastic housings and intake tube (not steel or aluminum) are used to eliminate the kinks, sharp bends and obstructions that can restrict airflow. The tube is tapered to accelerate airflow for more torque and better throttle response. Tube design also means the factory MAF sensor is positioned in the best spot to give you peak performance without triggering the CEL. Other 16-gauge steel components have a durable powder coated finish for an OE look. All trim is sealed or covered to lock out hot engine air. Easy to install! Although the stock air box, filter and intake tract are eliminated, the Magnum FORCE Stage 2 Air Intake System retains and works with your stock electronics. All stock mounting points are also retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Patented Pro-Guard 7 Filter is the best! Amazing 99.7% filtration efficiencyno other filter comes close! With five layers of progressively finer medical-grade cotton gauze and two layers of nonwoven polyester fabric, the Pro-Guard 7 offers the best engine protection you can buy! Absolutely essential for the roughest, toughest, dirtiest off-road driving conditions. Tall, rounded, open pleats maximize airflow and extend service intervals (45, 000 miles vs. 15, 000 for stock paper and 10, 000 for foam!). Most filters have built-in expanded metal to prevent collapse under high boost pressures. Best of all, you'll never have to buy another filter again because the Pro-Guard 7 filter can be washed, re-oiled and reused again and again.
The only choice for the enthusiast who wants all the power and torque he can get PLUS maximum protection against dirt and dust! Replaces factory air box, stock air filter and factory intake tube Improves airflow up to 75% Improves throttle response, acceleration and fuel efficiency Up to 60 ft./lbs. more of torque! Up to 50 HP gains! Includes Pro-Guard 7 filterthe best you can buyperiod! Cold air equals more power! That's why the Magnum FORCE Stage 2 Air Intake System REPLACES THE ENTIRE STOCK AIR INDUCTION SYSTEMso the absolute largest air box (and the largest filter!) can be used for your make and model. This guarantees that your vehicle is getting the maximum amount of air regardless of the performance upgrades. To further maximize airflow, heat-blocking roto-molded plastic housings and intake tube (not steel or aluminum) are used to eliminate the kinks, sharp bends and obstructions that can restrict airflow. The tube is tapered to accelerate airflow for more torque and better throttle response. Tube design also means the factory MAF sensor is positioned in the best spot to give you peak performance without triggering the CEL. Other 16-gauge steel components have a durable powder coated finish for an OE look. All trim is sealed or covered to lock out hot engine air. Easy to install! Although the stock air box, filter and intake tract are eliminated, the Magnum FORCE Stage 2 Air Intake System retains and works with your stock electronics. All stock mounting points are also retainedno cutting or drilling is required. Secured PEM nuts and welded and preassembled sheet metal speed up installation. Prepositioned opening for stock attachments means no dangling wires or hose/tube relocation. System comes with a limited lifetime warranty. Patented Pro-Guard 7 Filter is the best! Amazing 99.7% filtration efficiencyno other filter comes close! With five layers of progressively finer medical-grade cotton gauze and two layers of nonwoven polyester fabric, the Pro-Guard 7 offers the best engine protection you can buy! Absolutely essential for the roughest, toughest, dirtiest off-road driving conditions. Tall, rounded, open pleats maximize airflow and extend service intervals (45, 000 miles vs. 15, 000 for stock paper and 10, 000 for foam!). Most filters have built-in expanded metal to prevent collapse under high boost pressures. Best of all, you'll never have to buy another filter again because the Pro-Guard 7 filter can be washed, re-oiled and reused again and again.
Replaces factory air box, stock air filter, and factory intake tube Improves airflow up to 75%, throttle response, acceleration and fuel efficiency Increases up to 60 ft-lbs of torqueup to 50 HP gain! More air equals more power! For the automotive enthusiast who wants all the power and torque he can get! Compared to our other systems, the Magnum FORCE Stage 2 intake system replaces the entire stock air induction system. Remembering our motto ""Stock Sucks"", we eliminate the stock air box, the stock air filter and the stock intake tract. The only thing retained is the stock electronics. We make sure that our Stage 2 system, like all our intake systems, works with the stock electronics. Cold air equals more power! In designing out the stock air box, we design in the largest air box that we can for each vehicle application. Even though we make it as large as possible, we are careful to use the stock mounting points. There is no need to cut or drill anything when you install our system. We make the air box as large as possible so that we can get the largest air filter. At first glance you probably won't notice the unique features that we design into each air box. Each of them is there for a purpose, either to make your job of installing the system easier or to improve the performance of your vehicle. Here are a few the features and benefits that distinguish aFe's Magnum FORCE Stage 2 intake systems: 16-gauge powder-coated steel for a durable, OE look and finish Trim sealed or coveredseals out hot engine air Secured PEM-nuts for easier installation Welded and preassembled sheet metal for faster installation Pre-positioned opening for stock attachmentsno dangling wires, relocating hoses or tubes By designing the largest filter for the largest air box, we are able insure that the vehicle is getting the maximum amount of air regardless of the performance upgrades. System uses our conical universal clamp-on filters. Here are some common characteristics of our Pro 5R air filters: 100% poly urethane constructiondurable, resistant to high temperature and chemicals 5 layers of progressively finer medical grade cotton gauze Deep pleats for greater flow and dust holding capacity Rounded pleat geometry for better airflow characteristics Full or modified velocity stack for better airflow characteristics Washable/reusable filter media for longer service life Re oil with our restore kit sold separately (22441G). Our intakes systems use heat blocking molded tubes because you just can't bend a steel or aluminum tube to accommodate the modern engine compartment. With a molded tube, you can remove kinks, sharp bends and obstructions that restrict airflow. By tapering the tube, you can accelerate the airflow for more torque and better throttle response. We design our tube so that the factory MAF sensor is positioned in just the right place so that you get the best performance possible without triggering the CEL.
Replaces factory air box, stock air filter, and factory intake tube Improves airflow up to 75%, throttle response, acceleration and fuel efficiency Increases up to 60 ft-lbs of torqueup to 50 HP gain! More air equals more power! For the automotive enthusiast who wants all the power and torque he can get! Compared to our other systems, the Magnum FORCE Stage 2 intake system replaces the entire stock air induction system. Remembering our motto ""Stock Sucks"", we eliminate the stock air box, the stock air filter and the stock intake tract. The only thing retained is the stock electronics. We make sure that our Stage 2 system, like all our intake systems, works with the stock electronics. Cold air equals more power! In designing out the stock air box, we design in the largest air box that we can for each vehicle application. Even though we make it as large as possible, we are careful to use the stock mounting points. There is no need to cut or drill anything when you install our system. We make the air box as large as possible so that we can get the largest air filter. At first glance you probably won't notice the unique features that we design into each air box. Each of them is there for a purpose, either to make your job of installing the system easier or to improve the performance of your vehicle. Here are a few the features and benefits that distinguish aFe's Magnum FORCE Stage 2 intake systems: 16-gauge powder-coated steel for a durable, OE look and finish Trim sealed or coveredseals out hot engine air Secured PEM-nuts for easier installation Welded and preassembled sheet metal for faster installation Pre-positioned opening for stock attachmentsno dangling wires, relocating hoses or tubes By designing the largest filter for the largest air box, we are able insure that the vehicle is getting the maximum amount of air regardless of the performance upgrades. System uses our conical universal clamp-on filters. Here are some common characteristics of our Pro 5R air filters: 100% poly urethane constructiondurable, resistant to high temperature and chemicals 5 layers of progressively finer medical grade cotton gauze Deep pleats for greater flow and dust holding capacity Rounded pleat geometry for better airflow characteristics Full or modified velocity stack for better airflow characteristics Washable/reusable filter media for longer service life Re oil with our restore kit sold separately (22441G). Our intakes systems use heat blocking molded tubes because you just can't bend a steel or aluminum tube to accommodate the modern engine compartment. With a molded tube, you can remove kinks, sharp bends and obstructions that restrict airflow. By tapering the tube, you can accelerate the airflow for more torque and better throttle response. We design our tube so that the factory MAF sensor is positioned in just the right place so that you get the best performance possible without triggering the CEL.
Specifically designed for heavy-duty, high-temperature diesel engineswill not collapse Performance airflow and superior filtration A perfect replacement for original filterno modifications required! Constructed with 5 layers of fine-grade cotton gauze and 2 layers of non-woven synthetic polyester fabric surrounded by 2 layers of aluminum wire mesh. This allows the filter to hold more dirt and still has better airflow than any other filter on the market. Washable/reusablewill not collapse even when wet. Built-in expanded metal and 100% polyurethane construction withstands extreme engine temperatures and extreme conditions for an extended service life.
Cleaner is specifically formulated to release dirt without harming the microfibers critical to efficient filtration Specifically designed to work with AFE filters AFE's highly refined oil is proven less likely to foul MAF sensors than other oil
Top portion of the filter is molded together with the side portion to make one huge air filter Does not let dirt get into the motorgreat for the circle track, shifter kart or off-roading! Deep pleats are made of 100% engineering grade polyurethane TOP = T he O ne P iece! Top and bottom urethane rings have a bump seal that ensures tight, dust free sealing.
Black textured molded tube replaces factory intake tube and upgrades Stage 1 system Improves throttle response and improves acceleration Installs in less than 15 minutes! Increases up to 15 HP! Increases ft-lbs of torque! Reduces heat transfer to intake air! The factory intake tube often has baffles, sharp bends, and obstructions that send out flow restricting wake like pebbles in a stream. Others have constrictions in the diameter that further impede airflow. Our intake tubes feature smooth walls, gradual bends and transition chambers that straighten the airflow into the throttle body or turbo inlet. The tube is constructed of textured cross-linked molded plastic that cuts down the heat transfer from the hot engine compartment to the cold air flowing through the tube. More and more vehicles are equipped with increasingly sensitive Mass Airflow Sensors (MAF sensor) that are connected to the vehicle Engine Control Unit (ECU), the brains of the vehicle. The calibration of the MAF sensor and its position on the MAF sensor on the factory intake tube is designed to measure velocity and mass of the air flowing through the factory tube. If the velocity of the air moving over the MAF sensor is outside of the parameters programmed into the ECU, whether too fast or too slow; it will cause a lean stumble, engine error code and poor throttle response. We shape our tubes and position the MAF sensor to increase flow to the throttle body or turbo inlet while managing the velocity past the MAF sensor to keep its signal range within factory limits.
Black textured molded tube replaces factory intake tube and upgrades Stage 1 system Improves throttle response and improves acceleration Installs in less than 15 minutes! Increases up to 15 HP! Increases ft-lbs of torque! Reduces heat transfer to intake air! The factory intake tube often has baffles, sharp bends, and obstructions that send out flow restricting wake like pebbles in a stream. Others have constrictions in the diameter that further impede airflow. Our intake tubes feature smooth walls, gradual bends and transition chambers that straighten the airflow into the throttle body or turbo inlet. The tube is constructed of textured cross-linked molded plastic that cuts down the heat transfer from the hot engine compartment to the cold air flowing through the tube. More and more vehicles are equipped with increasingly sensitive Mass Airflow Sensors (MAF sensor) that are connected to the vehicle Engine Control Unit (ECU), the brains of the vehicle. The calibration of the MAF sensor and its position on the MAF sensor on the factory intake tube is designed to measure velocity and mass of the air flowing through the factory tube. If the velocity of the air moving over the MAF sensor is outside of the parameters programmed into the ECU, whether too fast or too slow; it will cause a lean stumble, engine error code and poor throttle response. We shape our tubes and position the MAF sensor to increase flow to the throttle body or turbo inlet while managing the velocity past the MAF sensor to keep its signal range within factory limits.
